prusaprinters
Ender 3 ADXL mount (Adafruit ADXL) for Ultimate Ender 3 Bed Leveling Knob
I was looking for a way to mount my ADXL345 for Klipper's input Shaper on my Ender 3, a...
3d printer solid bed mount
958 resultsSponsored
prusaprinters
thingiverse
Print-Rite DIY 3D - Y-Belt Spacer
My PrintRite DIY 3D printer came with a misaligned Y-Belt drive motor mount which was g...
thingiverse
Drag knife mount for Wanhao i3 Plus
Followed the steps here: https://www.instructables.com/id/Use-3D-Printer-As-a-Plottercu...
prusaprinters
Model Paint Bottle Holder
This is a holder for 7 bottles of Testors model paint. It is designed to mount under a ...
prusaprinters
Model Paint Bottle Holder
This is a holder for 7 bottles of Testors model paint. It is designed to mount under a ...
thingiverse
USB camera mount for Raspberry Pi
This is a way to use a USB port to mount a Raspberry Pi camera. I have a bunch of Ra...
SPONSORED
📈 Will the Fed cut interest rates in July?
Wall Street vs. the crowd. Who predicts the Fed correctly?
thingiverse
CubeX to RepRap Conversion Build - WIP
This is my work in progress to Convert a CubeX Trio into a RepRap 3D Printer. Features:...
thingiverse
Panel Mount Box
This is a panel mount that I made in FreeCAD 3D to mount a LED light control to my G-St...
prusaprinters
Ender front rail (Wyze) cam mount
I had been using a bed mounted mount for my Wyze cam but it seems to cause a lot of vib...
thingiverse
100mm ball for 3D scanning
Here is a 100mm 3D scanner target with internal support to make it printable without be...
thingiverse
Anet A8 Plus Y Axis Rod Mounts
The 3D printed Y axis rod mounts that came with my Anet A8 Plus were absolute garbage q...
prusaprinters
Prusa i3 plus / MK2 - Rasbery pi camera mount
Camera mount for Prusa i3 and standard rasberi PI camera module. Function: camera hold...
prusaprinters
Split Loom Wire Mounts
Designed these to work with 3/8 inch (Automotive style) split wire loom. It works SO mu...
prusaprinters
Split Loom Wire Mounts
Designed these to work with 3/8 inch (Automotive style) split wire loom. It works SO mu...
prusaprinters
Landing Gear Mount for Eflight Fury
Hi All This is a new 3D printable landing gear mount for the E flight Fury. This one is...
thingiverse
Salsa Jar Wall Mount (for Tostitos salsa jars)
Screws securely to (open) Tostitos glass salsa jars so that they may be fastened to a w...
prusaprinters
Cr10 Series Linear Rail (Y Axis)
Y Axis Linear Rail/Extrusion Mount. Uses 4x’s M4x10-12 Socket Head bolts and Hammer Nut...
thingiverse
100mm ball for 3D scanning V2
Here is a 100mm 3D scanner target with internal support to make it printable without be...
myminifactory
guitar wall holder
This is a piece i designed to hang my guitars on they are all on my wall because i see ...
cults3d
Ender 6 Orbiter v1.5 mount
Mounts the orbiter 1.5 to the ender 6 using the 2 top v wheel bolts, uses 4 x m3 captiv...
thingiverse
24V power supply SRS / relais extension box for 3d printer
I made a box to mount on a separate 24V power supply Until now, my 3d printer has been ...
prusaprinters
Orbiter LDO Motor Drag Chain Mount (10.x11)
Love the Orbiter extruder wanted a drag chain mount for my cables. Add some M3 heat set...
prusaprinters
Petsfang Right CR Touch Mount
My first remix of the right probe mount for the petsfang base Mount did not fit the CR ...
prusaprinters
TwoTrees Sapphire S upgrades
i made a few small upgrades for my TT Sapphire printer. There is an endstop mount for t...
prusaprinters
24V power supply SRS / relais extension box for 3d printer
I made a box to mount on a separate 24V power supply Until now, my 3d printer has been ...
cults3d
E3D V6 hotend mount
Hi, this is my cooling and mount solution for the E3D V6 hotend. It was developed to re...
thingiverse
MakerFarm Pegasus Single Bowden Mount with IR Sensor
After a few revamps and switcheroos, I've finally made a design worthy of printing. Th...
thingiverse
3D Printer Build based on TAZ5
I started a 3D printer build based on the modified TAZ X ends designed by TechsavvyCNC....
thingiverse
Eagle glider
This is a profile version derived from my RC eagle planhttps://www.rcgroups.com/forums/...
thingiverse
Bowden hotend mount for Geeetech i3. With 3D-touch and beefy chain for more electronics.
For my heavily modified Geetech Made this chain for use with Bowden E3D-V6 seup, wi...
Sponsored
Sponsored