thingiverse
8way Relay Mains Switchbox
A sturdy box to house a standard 8way relay board attached to 8 IEC outlets from two IE...
main relay 3D Models
801 resultsSponsored
thingiverse
grabcad
Honda PGM-FI Main Relay OBD1
PGM-FI Fuel Pump, ECU, Injector Main Relay MITSUBA (RZ-0132This relay powers up your EC...
prusaprinters
Main Power Restoration Delay / Equipment Saver
Where we live, power goes out a lot. “Like a-lot a-lot”. The real problem is when it ...
thingiverse
Main Power Restoration Delay / Equipment Saver
Where we live, power goes out a lot. “Like a-lot a-lot”. The real problem is when it ...
grabcad
91-95 Honda Civic 5th gen main relay connector
This is the main relay holder and female connector on ll 91-95 Hondas.
thingiverse
Main Relay Cover - Mitsuba RZ-0088 - for Honda Cars
Main Relay Cover for the Grey coloured Mitsuba RZ-0088 Relay. This might fit on all oth...
SPONSORED
📈 Will the Fed cut interest rates in July?
Wall Street vs. the crowd. Who predicts the Fed correctly?
thingiverse
Case for a Mains Voltage Relay Test Jig
Case for a mains voltage relay test jig. Can accept 5x7cm prototype boards. Unit shown ...
thingiverse
Mean Well LRS 350 housing with mains relay
I was looking for a MeanWell LRS 350 housing for my Ender 3. My intention for priority ...
grabcad
for Anshul Jain sorry about the delay
rotor and stator If you still want to change it, remember that the relationship is base...
pinshape
SCHUKO EU 230V Mains Plug Relay 2x NC/NO
SCHUKO EU Mains Plug with 2 Independent Auxiliary Contacts NC-COM-NO (relay) ALL FIL...
thingiverse
EU Schuko/Fr 230V Mains Plug Relay 2x NC/NO
European Schuko or French (with external ground pin) Mains Plug with 2 Independent Auxi...
thingiverse
Ender 3 power relay box
To auto shutdown your Ender 3 printer using Octipi and a relay breakout. Printed par...
thingiverse
4 relay board case for multiple socket outlet 220v Octoprint PSU and light
Hello, case to connect a 4 relay board for Octoprint PSU (x2 printers) and Leds Ligh...
thingiverse
Egg Turner
const int relayPin = 2; // relay digital signal pin unsigned int relayState = LOW; ...
thingiverse
Raspberry Pi & SKR E3 Turbo back case for Ender 3
Remix for BTT SKR E3 Turbo board (and Raspberry Pi) using 30mm back fans. On left si...
prusaprinters
Lack Table Leg Relay and Temperature Sensor Holder
I designed this mount to hold two relays and a temperature sensor controlled by Octopri...
grabcad
IOT BOX
Main relay box wall mount for IOT smart houses that controls lights.For more informatio...
thingiverse
Raspberry Pi Enclosure for Ender 5
Enclosure for Raspberry Pi, Buck Converter and Relay module. This set of electronic...
thingiverse
Raspberry Pi Case for Creality CR-10
Case made to host a Raspberry Pi 2/3 and a 2 relay module. I made two supports to scre...
grabcad
Advanced programmable relay PR103
Advanced programmable relay to control ventilation, heating, pumps and other equipment....
thingiverse
Solidstate relay mount for 25mm tube.
UPDATE - This SSR failed after about ten PPG starts so not recommended as a starter rel...
grabcad
Programmable relay with display and control buttons PR205DIN7
Advanced programmable relay with display and control buttons to control ventilation, he...
grabcad
Programmable relay with display and control buttons PR205DIN9
Advanced programmable relay with display and control buttons to control ventilation, he...
grabcad
Programmable relay with display and control buttons PR205DIN9
Advanced programmable relay with display and control buttons to control ventilation, he...
grabcad
Programmable relay with display and control buttons PR205DIN7
Advanced programmable relay with display and control buttons to control ventilation, he...
thingiverse
Relay Housing for Steve (the printer)
I needed a way to keep fingers out of mains voltage while attaching a relay to SkullSpa...
cults3d
Morning of Conflict Communications Center
When things get going on the morning of hostilities, relay those assets from orbit with...
thingiverse
Morning of Hostilities Communications Center
When things get going on the morning of hostilities, relay those assets from orbit with...
thingiverse
2 Pices of 4 relay modul holder
2 PICES OF 4 RELAY MODULE HOLDER It prints from two main pice that needs to be glued...
thingiverse
2-channel relay and optional Arduino Nano
This is a mounting bracket for the 2-channel version of those super common electro-magn...
Sponsored
Sponsored