grabcad
Orange RX RC receiver
Inventor single part file & iges & parasolid
orange rx 3D Models
37 resultsSponsored
grabcad
grabcad
Orange RX ORX R615
RC Reciever
thingiverse
Box for orange rx 433mhz
Box for orange 433mhz receiver Second version is with Zip Ties Print Settings Printer: ...
thingiverse
Orange RX Satellite Receiver R110X Holder
Holder for the R110X Satellite Receiver. Receiver snaps into the holder and then I use ...
cults3d
Openlrs, lrs, orange rx 1W case JR.
Openlrs, orange rx 1W case JR.
thingiverse
Openlrs, lrs, orange rx 1W case JR.
Openlrs, orange rx 1W case JR.
SPONSORED
📈 Will the Fed cut interest rates in July?
Wall Street vs. the crowd. Who predicts the Fed correctly?
cgtrader
Orange Mazda Rx 8 In Desert 3D model
Scene 09 Archexteriors vol. 15 Take a look at this textured and shadered visualization...
thingiverse
PixLite 16 Long Range Mk2 Tx and Rx
Mounting for PixLite® 16 Long Range Mk2 PCB board.https://www.advateklighting.com/produ...
thingiverse
Orange Rx 3 channel S.Bus receiver with long antenna leads holder
If you make one, please post a photo! A nice little protective housing and 90 degree ...
cults3d
1/144 RX-93 Nu Gundam Long Range Fin Funnel (Fukuoka 1/1 Version) For HG & RG RX-93 Nu Gundam
1/144 RX-93 Nu Gundam Long Range Fin Funnel (Fukuoka 1/1 Version) For HG & RG RX-93 Nu ...
grabcad
tEEonE TinyQuad 1
Sub 180 racing quad, 1306-3100 motors, CC3D Atom FC, Orange RX 615 receiver, Aomway 600...
myminifactory
250er Quadrocopter with CC3D (v2)
Because of the first 250er Quad design was to heavy I designed a lighter one.Last parts...
prusaprinters
Lemon Rx FPV stack mount with retaining clip
FPV stack mount with retaining clip for the Lemon Rx DSMX compatible PPM 8-channel dive...
thingiverse
Micro Quad V2
This is a 4 part mini quad design, its my first attempt. I wanted to sandwich the batte...
thingiverse
CC3D_ORANGE_R615X_MOUNT
CC3D and RX Mount Orange R615X, i print this with PLA, on a Craftbot Plus Print Setting...
thingiverse
250er Quadrocopter with CC3D (v2)
Because of the first 250er Quad design was to heavy I designed a lighter one. First...
thingiverse
250er Quadrocopter with CC3D
Simple self designed Quadrocopter with approximately 250mm diagonal from motor to motor...
thingiverse
Hitec Aurora 9 TX module case
This thing will snap into your Hitec Aurora 9 tranmitter module bay and allow you to cr...
thingiverse
R620X v1/v2 30.5x30.5 Mount
This is just an Simple Holder for an Orange RX 620X V1 / V2. The Mounting Holes are 30....
prusaprinters
Jeti DC-16 II case for external transmitter module / Jeti DC-16 II Gehäuse für externes Sendemodul
Hi,I have designed a small box for an external transmitter module for the Jeti DC-16 II...
thingiverse
Jeti DC-16 II case for external transmitter module
Hi, I have designed a small box for an external transmitter module for the Jeti DC-1...
thingiverse
1157 Housing for SA22C/FB Rx-7
Use the 3mf, the stl's settings might be off. This is an untested housing for the si...
thingiverse
Orange PI LCD mount Artillery SW-X1
This is OrangePI Zero mount for Artillery Sidewinder X1 which is mounted instead of the...
thingiverse
Pad-spacer insert for Shimano RS405 hydraulic brake calipers (Y8N218000 replacement)
This item can be inserted into the Shimano Tiagra RS405 hydraulic brake calipers to sec...
thingiverse
LoRaWAN Gateway case with GPS
This is my redesign of the excellent case design produced by @Amedee. I liked the ca...
thingiverse
PawxSpec Whoop | microquad racing fpv drone frame
****Hard to find the FC now. Such a shame because it was light, 2.2grams had OSD and co...
thingiverse
The Hangar's Stick Parts and Accessories
Parts and accessories to go along with The Hangar's stick design. Great, easy to fly rc...
thingiverse
Tiny Trak - Mini FPV Tank with OSD - 1S and 2S
**Introduction** ============= This is a servo driven tiny trak FPV tank with the pos...
cults3d
RX Manual Glock Gel Blaster Custom Slide
Be warned, fitting this is a bit of work and will require some 'smithing' to get the bl...
thingiverse
RX Manual Glock Gel Blaster Custom Slide
Be warned, fitting this is a bit of work and will require some 'smithing' to get the bl...
Sponsored
Sponsored